当前位置: 首页 > 文章 > 人工林杨树木材性质与单板和胶合板质量关系模型的探讨 林业科学 2000 (1) 93-98
Position: Home > Articles > A MODELING APPROACH TO THE RELATIONSHIPS BETWEEN PLANTATION POPLAR WOOD PROPERTIES AND QUALITIES OF VENEER AND PLYWOOD Scientia Silvae Sinicae 2000 (1) 93-98

人工林杨树木材性质与单板和胶合板质量关系模型的探讨

作  者:
鲍甫成;刘盛全;江泽慧
单  位:
安徽农业大学;中国林业科学研究院
关键词:
人工林杨树;木材性质;单板和胶合板;模型方程
摘  要:
本文以生长在3 种长江滩地类型( 江滩、洲滩、湖滩) 、3 种栽植密度(3m ×4m ,4m ×5m ,5m ×6m) 下的3 个品系人工林杨树,即[ 欧美杨无性系72 杨( Populus×euramericana cv.Ⅰ- 72/58) ,美洲黑杨无性系63杨( P.deltoidescv .Ⅰ- 63/51) 和69 杨( P.deltoides cv .Ⅰ- 69/55)( 以下简称72 杨,63 杨,69 杨) 为对象,在研究人工林杨树木材性质与单板和胶合板质量关系的基础上,先用逐步回归筛选有关关键材性指标,然后再进一步模拟人工林杨树木材性质与单板和胶合板质量之间的关系。结果表明,长江滩地72 、63 、69 杨单板和胶合板质量能够用与之相关的木材性质指标进行多元线性回归模拟。单板厚度偏差( VVT) 随纤维宽度( FW) 、木纤维比量( FP) 、导管比量( VP) 变化的模型为:VVT= - 3-414 + 0-063 FW+ 0-049 RP- 0-033 VP单板背面裂隙率( RLC) 随木材弦面硬度( TH) 、抗弯弹性模量( MOE) 、气干密度( WD) 和体积全干干缩率( SV) 变化的模型为:RLC= 9-472 + 0-005 TH+ 0-?
译  名:
A MODELING APPROACH TO THE RELATIONSHIPS BETWEEN PLANTATION POPLAR WOOD PROPERTIES AND QUALITIES OF VENEER AND PLYWOOD
作  者:
Bao Fucheng 1) Jiang Zehui 3) (Chinese Academy of Forestry Beijing100091) Liu Shengquan 2) (Anhui Agriculture University Hefei230036
关键词:
Plantation poplar trees, Wood properties, Veneer and plywood, Modeling equations
摘  要:
Three variaties of plantation poplar trees( Populus×euramericana cv.I-72/58, P.deltoides cv.I-63/51 and P.deltoides cv.I-69/55)growing in three different types of beaches along Yangtse River and in three different planting densities were extracted as the testing materials to model the relationships between wood properties and quality of veneer and plywood of poplar plantations in this study.Based on the relationships found in the former study,first the stepwise regression analysis was used for sifting out the key wood properties concerned,and then the polybasic,linear regression was used for modeling the relationships.The results show that the qualities of veneer and plywood of poplar plantations,can be well modeled with the wood properties by means of polybasic linear regression analysis.\;The modeling equation of the variation of veneer thickness (VVT) varying with fiber width (FW) ,proportion of vessel (VP) and fiber (FP) is:\; VVT=-3 414+0 063 FW+0 049 RP-0 033 VP The modeling equation of the ratio of lathe check (RLC) varying with wood hardness in tangential (TH), modules of elasticity (MOE) ,wood density in air\|dry (WD) and volumetric shrinkage of wood in oven\|dry (SV) is:\; RLC=9 472+0 005 TH+0 003 MOE+8 366 WD-2 302 SV The modeling equation of the gluing strength of plywood (GS) varying with pH values(pH),fiber length (FL) ,fiber width (FW) ,vessel length (VL) and proportion of vessel (VP) and ray (RP) is: GS=3 326-0 268 pH -0 002 FL+0 191 FW-0 004VL-0 033 VP+0 095 RP The significances for the above modeling results were found greater than 0.73 while the relative error between the measured and predicted values was around 20%.Thus,the reliablity of those modeling equations could be recoglized.

相似文章

计量
文章访问数: 3
HTML全文浏览量: 0
PDF下载量: 0

所属期刊

推荐期刊