中国农业科学院农业信息研究所 中国农学会
Agricultural Information Institute of CAAS China Association of Agricultural Science Societies
En
Ch
中国农业科学院农业信息研究所 中国农学会 主办

AI检索

订阅

返回顶部
当前位置: 首页 > 文章 > 竹单板条层积复合材制备工艺及物理力学性能 东北林业大学学报 2018 (10) 71-77
Position: Home > Articles > Preparation Technology and Mechanical Properties of Bamboo Veneer Strips Journal of Northeast Forestry University 2018 (10) 71-77

竹单板条层积复合材制备工艺及物理力学性能

作  者：
侯云艳;程万里;宣丽慧;高珣;李庆德;周建波
关键词：
竹材;竹单板;竹单板层积复合材;制备工艺;物理力学性能
摘  要：
以竹单板条、酚醛树脂(PF)胶黏剂、异氰酸酯(PMDI)胶黏剂为主要原料,按照设计的工艺流程制备了竹单板条层积复合材(PBSC);采用正交试验法,分析竹单板条原料规格尺寸、PF和PMDI两种胶黏剂溶液质量分数及浸渍时间对PBSC物理力学性能的影响,遴选制备PBSC的适宜工艺参数。结果表明:在实验范围内,PBSC物理力学性能随着胶黏剂溶液质量分数增加而增强,PF和PMDI两种胶黏剂质量分数为30%时PBSC力学性能均最佳,弹性模量分别为9 780、9 840 MPa,静曲强度分别为121.08、124.34 MPa,均达到GB/T20241—2006《单板层积材》结构用单板层积材100E优等品等级的规定值;浸渍时间为60 min时,性能最佳;单板条的尺寸规格对PBSC静曲强度和弹性模量的影响不显著; PF和PMDI浸渍处理的竹单板条制备的PBSC,物理力学性能无明显差异。
译  名：
Preparation Technology and Mechanical Properties of Bamboo Veneer Strips
作  者：
Hou Yunyan;Cheng Wanli;Xuan Lihui;Gao Xun;Li Qingde;Zhou Jianbo;Northeast Forestry University;Beihua University;Qiqihar University;Beijing Forestry Machinery Research Institute of The State Forestry Administration;
单  位：
Hou Yunyan%Cheng Wanli%Xuan Lihui%Gao Xun%Li Qingde%Zhou Jianbo%Northeast Forestry University%Beihua University%Qiqihar University%Beijing Forestry Machinery Research Institute of The State Forestry Administration
关键词：
Bamboo;;Bamboo strips veneer;;Parallel bamboo strand composite;;Preparation technology;;Mechanical properties
摘  要：
The bamboo parallel,phenol formaldehyde( PF) and icocyanate resin adhesives( PMDI) were used to prepare the parallel bamboo strand composite( PBSC) according to the designed process flow. The effects of the raw material size,mass fraction and dipping time of phenol formaldehyde and icocyanate resin adhesives( PMDI) on the mechanical properties of PBSC were evaluated by using an the orthogonal experimental. The suitable process parameters for preparing PBSC were selected. Within the experimental range,the mechanical properties of PBSC was increased with the content of adhesives. The performance of PBSC reached the best values when the phenol formaldehyde and isocyanate adhesive content were 30%,with MOEs of 9 780 and 9 840 MPa,and MORs of 121.08 and 124.34 MPa,respectively,both meeting the national standard GB/T20241-2006"laminated veneer lumber"structural veneer lumber 100 E class grade requirements. The best mechanical properties appeared when the dipping time was 60 min. The effects of the veneer strips size on the MOR and MOE of PBSC were not significant. There were no significant differences in mechanical properties of BPSL impregnated by phenol formaldehyde and isocyanate resin adhesives.

相似文章

导出引用
计量
文章访问数: 14
HTML全文浏览量: 0
PDF下载量: 0

所属期刊

推荐期刊

友情链接Friendly link
农业信息研究所Agricultural information institute 农业智能知识服务平台Agricultural intelligent knowledge service platform 农业学术服务平台Agricultural Knowledge Service System 中国知网CNKI 维普网VIP 万方WANFANG DATA
联系我们Contact us

电话Tell：010-82109652-808

邮箱E-mail：agrijournal@caas.cn

服务Service
关于我们About us 意见建议Opinions and suggest
版权说明Copyright
单位：中国农业科学院农业信息研究所 中国农学会 © 2017中国农业科学院农业信息研究所 ICP备案号：京ICP备09089781号-46